size list specifications dimensions (unit : mm) t 1 please reduce 0.25v per 1 c from over 85 c for 25v products. t 2 in case of some problems for measured values, measure after applying rated voltage for 6.3 to 16 and 30v products or temperature derating voltage for 25v products for 30 minutes at 105 c . rv : rated voltage (sv) : surge (room temperature) t for the minimum packing quantity, please refer to page 53. size code a b c d e f 4.0 5.0 6.3 6.3 8.0 10.0 d 0.5max. lmax. 7.8 7.8 7.8 10.8 11.5 11.5 0.45 0.45 0.45 0.60 0.60 0.60 0.5 0.5 0.5 0.5 0.8 0.8 0.5 0.5 0.5 0.5 0.8 0.8 2.0 0.5 2.0 0.5 2.5 0.5 2.5 0.5 3.5 0.5 5.0 0.5 f d 0.05 gmax. kmax. f g a' c k a b b' standards of terminal lead position sleeve d l 15min. 4min. 19min. d f mark ; ideal terminal lead position c; the middle point of a-a' 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 a b c a b c d a a b b c d d a a b b c c c d e f f a b b c d d e f rv f 6.3 (7.2) 16 (18.4) 25 (25.0) 10 (11.5) 30 (34.5) (sv) -55 c to +105 c m : 20% less than or equal to the value of table13 less than or equal to the value of table13 less than or equal to the value of table13 -55 c +105 c ? c/c tan leakage current ? c/c tan leakage current ? c/c tan leakage current z / z 20 c z / z 20 c 0.75 to 1.25 0.75 to 1.25 within 20% 1.5 times or less than an initial standard below an initial standard within 10% 1.5 times or less than an initial standard below an initial standard within 5% below an initial standard below an initial standard (after voltage processing) items characteristics endurance damp heat (steady state) resistance to soldering heat characteristics of impedance ratio at high temp. and low temp. conditions category temperature range tolerance on rated capacitance tangent of loss angle leakage current esr 120hz 120hz 105 c, 2,000h, rated voltage applied (25v 20v applied) t 1 60 c, 90 to 95%rh, 1,000h, no-applied voltage flow method (260 5 c x 10s) t 2 based the value at 100khz | +20 c after 2 minutes 42 sc aluminum solid capacitors with organic semiconductive electrolyte rohs compliance suitable for noise limiters and switching power supplies that make a point of high frequency characteristics. also, make use of it when needed long life span and high reliability. sc 4 f s j f t standard radial lead type
t 1 tolerance on rated capacitance : m 20% t 2 after 2 minutes t 3 100khz, +45 c temperature coefficient for allowable ripple current 30sc1m 25sc1m 25sc1r5m 16sc2r2m 16sc3r3m 10sc4r7m 6sc6r8m 30sc1r5m 30sc2r2m 25sc2r2m 25sc3r3m 16sc4r7m 16sc6r8m 10SC10M 6sc15m 30sc3r3m 25sc4r7m 25sc6r8m 25sc10m 16sc15m 10sc22m 6sc33m 30sc4r7m 30sc6r8m 25sc15m 16sc22m 16sc33m 10sc47m 30sc10m 25sc22m 30sc22m 25sc33m 25sc47m 30 25 25 16 16 10 y 6.3 30 30 25 25 16 16 10 y 6.3 30 25 25 25 16 10 6.3 30 30 25 16 16 10 30 25 30 25 25 1.0 1.0 1.5 2.2 3.3 4.7 6.8 1.5 2.2 2.2 3.3 4.7 6.8 10 15 3.3 4.7 6.8 10 15 22 33 4.7 6.8 15 22 33 47 10 22 22 33 47 350 350 300 280 280 280 250 300 250 200 200 180 150 150 120 200 100 100 90 90 70 70 120 120 70 70 70 60 110 40 80 35 35 430 430 435 450 500 540 560 435 695 695 700 720 745 780 815 820 1130 1140 1150 1230 1270 1320 1300 1340 1650 1800 1900 2020 1380 2330 1830 2900 2980 0.03 0.03 0.03 0.04 0.04 0.05 0.05 0.03 0.03 0.03 0.03 0.04 0.04 0.05 0.05 0.03 0.03 0.03 0.03 0.04 0.05 0.05 0.04 0.04 0.04 0.05 0.06 0.06 0.06 0.06 0.06 0.06 0.06 1.00 0.50 0.50 0.50 0.53 0.50 0.50 1.00 1.32 0.55 0.83 0.75 1.09 1.00 0.95 1.98 1.18 1.70 2.50 2.40 2.20 2.08 2.82 4.08 3.75 3.52 5.28 4.70 6.00 5.50 13.20 8.25 11.75 a b c d e f table13 sc series characteristics list size code part number t 1 rated voltage (v) rated capacitance ( f) esr 100khz to 300khz (m ? ) (max.) allowable ripple current (marms) t 3 tangent of loss angle (max.) leakage current ( a) (max.) t 2 ambient temp. coefficient tx ? 45 c 1 45 c ? tx ? 65 c 0.85 65 c ? tx ? 85 c 0.7 85 c ? tx ? 95 c 0.4 95 c ? tx ? 105 c 0.25 frequency coefficient for allowable ripple current 120hz ? f ? 1khz 0.05 1khz ? f ? 10khz 0.2 10khz ? f ? 100khz 0.5 100khz ? f ? 500khz 1 frequency coefficient 43 sc aluminum solid capacitors with organic semiconductive electrolyte rohs compliance
|
